|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
350~1000mA Multi-current LED Driver(2×25W) with 1-10V & Switch Dimming Function
|
|
| Model No.︰ | HE2050-A2 |
| Brand Name︰ | HYTRONIK |
| Country of Origin︰ | China |
| Unit Price︰ | - |
| Minimum Order︰ | 10 pc |
|
|
|
|
|
|
|
1-10v dimmable multi-current LED driver -- HE2050-A2
- Recommended for 2×25w;
- 1-10v dimming interface;
- 1-100% dimming range;
- Multi-current 250/350/400/450/500/550/600/700mA;
- Efficiency >86%;
- Power factor >0.9;
- Over-heat protection with auto-reset;
- Short circuit protection with auto-reset;
- Working temp. -25℃ to +50℃ ;
- For independant installation.
LED current selection:
This multi-current LED driver has covered the normal curren in the market. The current can be easily configured by choosing the correct combination of the DIP switches. Warning: please make sure the correct current is selected before switching on the driver!!! (Over-current may cause serious damage to the LED, while under-current does not give the full light output of the LED.)
Switch-Dim:
- On/off: Short push(50-400ms) on the switch.
- Stepless dimming: Long push and hold ( > 400ms) on the switch.
- For fine tuning of light level: With every 2nd long push,the light level goes the opposite direction.
- Built in with permanent memory: Light returns to the previous dimming level when switched off and on again, even at power failure.
Sychronization:
No limitation on the number of drivers when connected to the same switch, Thanks to the MCU program.This means there is no need for any additional synchrony wire in large installation, where many drivers should be controlled by 1 switch.
Re-synchronization:
When users push the switch too fast and too often during a short period of time, the drivers may not output the same current, and the LED may have different brightness, in such case, we just need to- 1. short push to switch off the light, and then.. 2. a long push to start up the lighting, then all LED will be synchronized and stays in the same brightness. This driver can also be reset by short-circuit the 1-10v terminals.
Permanent memory:
This driver has buit-in permanent memory against power failure, the light always start up at the previous level when they were switched off last time.
Detailed Data Sheet:
| Input voltage |
220-240VAC 50/60Hz |
| Rated current |
0.25A (Max) |
| Rated power |
2×28W (MAX) |
| Output voltage |
60VDC (Max) |
| Operation frequency |
320kHz ≥f≥50kHz |
| Powor factor |
≥0.90 |
| Operation temperature |
Ta: 50℃ Tc: 75℃ |
| Output current & Load |
250mA(1-16pcs) 350mA(1-16pcs)
400mA(1-16pcs) 450mA(1-13pcs)
500mA(1-12pcs) 650mA(1-11pcs)
600mA(1-10pcs) 700mA(1-10pcs) |
| Max. Efficiency |
≥86% |
| Abnormal protection |
Output short-circuit protection with auto-reset |
|
|
|
| Over-heat protection |
Over-heat protection with auto-reset |
|
|
|
| EMC standard |
EN56015 EN61547 |
| Safety standard |
EN61347-1 EN61347-2-13 |
| Certification |
CE SEMKO EMC |
| Dielectric strength |
Input—Output: 3750VAC
Input—Ground: 1800VAC
Output—Ground: 500VAC
All with 5mA/1min |
| Ip grade |
IP20 built-in type |
|
|
|
|
| Price Terms︰ | FOB Guangzhou |
| Payment Terms︰ | TT/PAYPAL |
| Packing︰ | CTN |
| Lead Time︰ | 5~7 working days |
| SKU︰ | 1000 |
| Standards Certificate︰ | CE SEMKO EMC |
| P.S.︰ | If not sure about anything on this page then why not ask us a question? |
|
|
Product Image
|
|
|
Related Products
|
|
|
|
|
|
|
|
|
|
